You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
switched
A switched capacitor (SC) is an electronic circuit element implementing a filter. It works by moving charges into and out of capacitors when switches are opened and closed. Usually, non-overlapping signals are used to control the switches, so that not all switches are closed simultaneously. Filters implemented with these elements are termed "switched-capacitor filters", and depend only on the ratios between capacitances. This makes them much more suitable for use within integrated circuits, where accurately specified resistors and capacitors are not economical to construct.SC circuits are typically implemented using metal–oxide–semiconductor (MOS) technology, with MOS capacitors and MOS field-effect transistor (MOSFET) switches, and they are commonly fabricated using the complementary MOS (CMOS) process. Common applications of MOS SC circuits include mixed-signal integrated circuits, digital-to-analog converter (DAC) chips, analog-to-digital converter (ADC) chips, pulse-code modulation (PCM) codec-filters, and PCM digital telephony.
Long story short I have a leak from possibly the flexi hose that connects to the upstairs hot water tap.
I've switched off the boiler and mains water and waiting on a plumber but not sure when they'll arrive.
My question is if I leave the boiler off and then turn the water back on so I can use...
Our Potterton EP2 was old and the sliders for HW/CH were loose. We couldn't get CH without the HW on! So I put a new digital EP2 on. It fit over the old backplate : no wiring required! What I found then was that if I put HW on with the slider then fine - digital display come on "Hot Water" and...
Replaced Grundfos Ups 2 C/H pump with a Ups3. when c/h only on no problem as soon as h/w is on as well gurgling and air in system experienced, also hot water coming out of 22mm vent into expansion tank ( doesn't happen when only c/h is on) so bad that h/w must be turn off. I had no problem...
Radiator in hall has no TVR, thermostat on hall wall set to frost protection and boiler set to hot water only, however radiator in hall is producing heat? Why is this and why needs to be done to solve issue?
Hi All,
New to this so not sure if posting this questions is valid, but i have a boiler issue which has baffled me.
I have a Glow Worm Micron 120 boiler and it recently decided to die all of a sudden. I have had issues with the PCB in the past i.e i resoldered some dry joints a year ago. Thus...
Hi all, newbe here. Just replaced a o ring on the ideal isar he30 boiler diverter valve manifold and all went great but now the boiler displays 0 on the panel but the radiators are still getting warm when switched off. Has anyone got any ideas what is going on, cheers,
Hello all,
Apologies A) for showing my ignorance and B) possibly asking a question that has been answered elsewhere - though I have looked!
I have a problem with the heating on a pub I have taken over. The boiler has been recently overhauled and works fine, but I'm struggling to control it...
My system comprises a Kingspan 180L unvented hot water tank, Danfoss FP715si controller and a Bosch Worcester Greenstar Ri boiler, which works perfectly as far as I can see (and is serviced by BG every year).
The problem is that the CH pump will only start if I switch the HW to manual, if they...
Hi
for a few reasons (problem with hot water, possible smart heating installation), I familiarised myself with my heating system and wiring. Looks like a standard S-Plan with magnetic valves for hot water, central heating and UFH. Valves are controlled by normal standard backplate programmer...
The radiators were taken off and the boiler was switched off as was the water supply.
Would switching the water supply back on cause a leak? The only taps are the bathroom and kitchen which have their own stop valves. The toilet has not been removed.
Hi folks. I have a couple of issues, any help advice much appreciated.
1. When my hot water tank thermostat demands hot water (wired into Honeywell wiring centre), I do not get a switched live to the boiler. I get 69 volts ac for both on and off wires from the tank stat. I have fitted a new tank...
Hi all,
I have installed Viessmann vitodense 100 combi boiler and about to connect to my wiring center, I could not find to which connector/port on the boiler should I wire switch live. Has anyone experience with this?
PMSL. Just realised I was trying to get rid of some monopoly on accreditation here by changing the name of a forum category. Not sure that'll work. :D :D :D
Name changed back. We'll try and tackle the monopoly another way some other day lol
Hi All,
We have a greenstar 15ri boiler, what I believe is a vented cylinder and two tanks in the attic. About 10 minutes or so after the heating or hot water is switched on there are loud bangs/scraping noises coming from pipes next to the cylinder. We believe the culprit is an aerjec2 that...
Is it likely there could be a leak in a join /copper pipe work that only really occurs when water is either flowing through or when it is initially filled/pressurised - as opposed to statically sitting in the pipe under mains pressure?
The actual scenario is the mains was switched on and off...
I have a Camray 5 90 external combi oil fired boiler. I replaced the 3 port valve body only as it was leaking and after that seemed to work ok. However shortly after when CH was being called for the accuator wasnt moving and had to manually be moved to man position to get CH. However the other...
Having issues with the boiler making a arcket when hot water/heating running, sounds like combustion needs resetting as it runs perfectly for 10 minutes then error E comes up and flame symbol. Boiler restarts and runs perfectly again until next time which could be never or 30 minutes
Service...
Hi there,I bought a new tap from Screwfix. It is a Watersmith Heritage cubic single lever monoboc mixer kitchen tap.
The problem is that when it is switched off it runs a small amount of water for about 10 seconds, then drips for about 10 seconds and goes completely off. I looked at the reviews...
Hello folks looking for some help here my brothers house an open vented system . Ideal classic ff240does not fire up
When heating is switched on. Boiler only fires up when hot water is switched on. Checked power to boiler also pump rums when heating switched on but still does not fire up. Anyone...
tartanarmyman
Thread
boiler
central
central heating system
classic
hot
hot water
ideal
no central heating
pumps
switched
water
Dear All
I recently had the above Vaillant stem boiler with megaflo system installed.
I have 2 issues if someone could please kindly help:
1. When I check the control panel no hot water tap symbol appears. Only the radiator symbol even when hot water is switched on. Is this normal or do I...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.