You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
no heating
Heating oil is any petroleum product or other oil used for heating; a fuel oil. Most commonly, it refers to low viscosity grades of fuel oil used for furnaces or boilers use for home heating and in other buildings. Home heating oil is often abbreviated as HHO.Most heating oil products are chemically very similar to diesel fuel used as motor fuel; motor fuel is typically subject to higher fuel taxes. Many countries add fuel dyes to heating oil, allowing law enforcement to check if a driver is evading fuel taxes. Since 2002, Solvent Yellow 124 has been added as a "Euromarker" in the European Union; untaxed diesel is known as "red diesel" in the United Kingdom.
Heating oil is commonly delivered by tank truck to residential, commercial and municipal buildings and stored in above-ground storage tanks ("ASTs") located in the basements, garages, or outside adjacent to the building. It is sometimes stored in underground storage tanks (or "USTs") but less often than ASTs. ASTs are used for smaller installations due to the lower cost factor. Heating oil is less commonly used as an industrial fuel or for power generation.
Leaks from tanks and piping are an environmental concern. Various federal and state regulations are in place regarding the proper transportation, storage and burning of heating oil, which is classified as a hazardous material (HazMat) by federal regulators.
So I have a vaillant combi boiler.
2 zones with a valve each controlled by Nest system.
When my Nest calls for heat zone one opens up and I have hot flow to manifold, pipes thus hot radiators.
When the other Nest calls for heat zone 2 valve opens up hot flow to manifold but no hot...
Hi all
I'm new here so thanks in advance, I have an old Netaheat boiler set up (gravity fed) which failed to fire up for central heating last week, I have set the three way diverted valve to manual and have been using the "call for hot water" to heat the radiators (once its been on for half...
i have an Ideal Espirit 2 boiler, the water is working perfect but the heating is not working.
We had a new pump fitted about 12 months ago, I've had three tradesman in and they have all said sometime different; one said I needed a new pump the other said I needed a new programmer and the...
hi, we have a problem with are heating, when it is switched on nothing happens, we have a Honeywell st9400c programmer and just set to to continuously when we want heating on, the light comes on but nothing is happing at the boiler, we can switch it to heat water and the boiler fires up straight...
Hi all,
I hope this is the right category.
I woke up this morning in a cold house with no hot hot either. (It's a rent flat).
My boiler Potterton Prima F50 is continuously running, I can see fire inside, it's making the usual noise apart of that gurgling water noise.
I checked the...
GeorgeN
Thread
boiler
central heating system
hot
hot water
noheating
oil
potterton
water
won't
Would really appreciate thoughts
We have an ICOS HE15 (now nearly 9 years old - installed in new build), I installed a tado v1 about 4 years ago, and just upgraded to the v3 model 2 weeks ago. All worked at first, but now I have absolutely no central heating whatsoever. I do have hot water...
Hello people
went to a boiler break down today, it was a worcester 28i rsf combi boiler. Boiler hot water output was fine. But no central heating.
turn heating demand on fan runs, pumps runs, but no ignition. No lock out light flash. Checked overheat stat on top of the boiler has continuity...
We have a Gloworm boiler and a Boilermate2000 up at the top of the house; a workman put a hole in a pipe today (tucked in the corner of the house no less) for hot water. This meant a good 90 minutes of the water going everywhere until it drained away.
Plumber arrived and fitted a compressor to...
alf1234
Thread
boiler
boilermate
central heating system
noheating
should
water
Hi,
I have a Worcester Bosch Greenstar 24i system, installed in 2009 with a megaflop indirect cyclinder. The primaries are 28mm, split into a 28mm 2-port for heating and a 22mm 2-port for hot water. The 28mm 2-port for CH was changed and is wired correctly.
The issue is if the hot water is on...
Hi People,
Im new to this site so be nice!! Ive been working on a Ideal Isar 24 today (Not a favoute of mine) the hot water is working fine but when stat/timer are calling for heat all i get on the dispaly is c and flashing burner No fault code.
I have tryied replacing the PCB but still the same...
Hi,
I attended a job with no heating but perfect hot water. When heating is selected status goes to 'c' and burner goes solid on for about 20 seconds then goes to flashing. No fault codes.
I initially suspected the diverter but oddly the flow pipe from the boiler is roasting and the return...
Hi Guys,
I thought I would be best off asking for this one in lieu of the wealth of advice on here.
I have a landlord with a halstead ace high combi, boiler fires and stay on all appearing to run fine, no noise, no over expansion. However when heating is switched on pump runs, fan runs...
Hi all,
Last night we tried to turn on the heating for the first time this autumn and it turns out it is not working. The hot water works fine, the flame comes on periodically to heat it even when not in use, but the radiators are completely cold, no hot water is coming out their way. Do not...
kkd
Thread
eco
flame
heating
hot
hot water
noheating
please
potterton
radiators
tried
water
Just a quick one guys. Went to a worcester 24i rsf the other day on a breakdown. Basically it has hot water but doesn't fire up on heating....
however if you run the hot tap prior to turning on heating then turn hot tap off. boiler stays fired up on heating. I gave it a good service as it hadnt...
Hi
Ive been called to look at a remeha avanta plus 28c with hot water working fine just no heating. No fault codes are showing up at all. Is there anyway of checking the motorised valve or the divertor as im not that familiar with these boilers apart from having to change the seals and ignition...
Hi all,
right, so, please help a man out here :-)
my plumber for some unknown reason whilst plumbing the kitchen in that we have just fit confused the hot feed from the boiler and put a cold feed onto it......
the heating was working fine and as normal,
until...
my heating guy came out...
Having problems with above mentioned thermostat. Been running with no issues for 10 years. A jumper fell out today from the back of the control unit, and I must've replaced it incorrectly as when I opened the receiver later on to troubleshoot, I saw that they weren't corresponding. I only...
osh
Thread
blown
heating
help
mains
noheating
power
receiver
salus
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.