Rad is only a few years old.
Paint is flaking away at the top curved section and it looks like faint spots of rust where the rad is now bare.
Hello to everyone.Im a newbie here. plumbing & heating+GSR engineer.
Every two weeks or so I have to go and top up the system because the hot taps are running cold. Boiler display is flashing 0.6 bar and I fill up to 1.3. I've had an engineer look inside the boiler and he can't see anything wrong. I've checked the pipes all over the house and cannot see any...
The left rear floor corner is highest (the shower pan touches/sits on the floor), sloping down diagonally to the front right corner (lowest). The front right corner shim is 5/8", the left front corner is 3/8" shimmed, with shorter shims under left middle and right rear corner.
The pan perimeters...
- Question
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold then would get hot water most of the time. Changing the flow cartridge about 2 years ago (when I moved in) solved this problem enough to suffer it as...
Our kitchen mixer tap has started dripping. Like so much of the plumbing in our almost new build bungalow, it is lacking! The plumber didn't install any isolating cocks in the H&C feed to the tap so how can I identify which of the valves is passing? Shut the whole H&C water system down?
I am in process of replacing an existing sink with a new stainless steel one. The existing tap is plumbed directly to copper which means that it is earthed. The new tap will use flexible tails and so will not be earth bonded. My initial search for information suggests that there is no legal...
Hi everyone,
Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
We are from Alberta, and I own an electrical company.
I have been asked by a BC Mechanical P. Eng. to install an emergency STOP button at the man-door to the boiler room. It's intent is to 'halt' the operation of the boilers in the room should there be an emergency. He is demanding that I do...
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
I have had a look at previous posts and think I know the answer to this but just before I make it worse could I just check what you think about this one.
Granddaughter just moved house and this valve decided to leak when it was closed.
When open its fine.
Normally I have repacked the gland on...
Show us your fanciest radiators you've installed! We would love to see them!
I love this Milano vertical radiator in the kitchen space.
What do you think?
Hello all,
I'm would like to extend an existing outside tap to another point in the garden. I'm about to pour a concrete patio and was hoping to run the water line underneath. There are existing drain (and who knows what) pipes running along the same wall so I'm nervous about digging too far...
Hello all,
I’m replacing a concrete paving slab patio in the back yard. The original patio used 50mm deep concrete slabs on hardcore & sand. I’m planning to pour a 100mm deep concrete patio on 100mm hardcore. In order to achieve the same final height to line up with the rest of the patio, I...
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Can anyone recommend a decent multi meter, preferably under a 100 pounds. It's for checking boiler components so I don't need a top spec one ....just easy to use and reliable.
The fluke 115 looks good but its above my budget. My current socket and see one was great but it's developed a fault.
Hi they used to say as a last resort you could discharge the D2 pipework at high level and turn it back to the wall. Similar to a combi boiler. I have just looked back through the regs this seems to have changed and it isn't mentioned now. It now mentions if at high level it should be discharged...
- Question
is it feasible to connect a flo force or saniflo shower pump drain to a washing machine standpipe
I have an old Modena 80 E combi boiler that is randomly short cycling on windy days. The burner goes out and re-ignites within a few seconds and continues to burn for between five and forty seconds before stopping again. Under normal conditions the boiler works fine but as soon as it gusts over...
Does anyone know where I can get one of these? Toilet is leaking into the bowl. This one pushes in with a half turn but I can't find one anywhere.
Creating content since 2001. Untold Media.
Newest Plumbing Threads
-
-
No Hot water, Fixed and Broken Again Ideal Logic 24
- Started by Filthbags
- Replies: 0
-
-
What's happening to this radiator, paint flaking off?
- Started by mikmikmikmik2024
- Replies: 2
-
Is it necessary to earth bond a Kitchen Sink?
- Started by Cello
- Replies: 2
-
Show us your fanciest radiators you have installed!!
- Started by Lou
- Replies: 0
-
Y Plan, no hot water but heating is working when called
- Started by Chopper9495
- Replies: 8
-
-
Towel Rail Valve Advice please (35 Characters needed.)
- Started by NorthernLad
- Replies: 6
-
Unvented discharge at high level current regs
- Started by Matt0029
- Replies: 11
-
Trying to source a dual-flush valve
- Started by Thomas J Marshall
- Replies: 2
-
-
-
-
What constitutes a Commercial Appliance and thus a Commercial Kitchen?
- Started by FozzieBear
- Replies: 3