You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
mixer
A mixer, depending on the type, also called a hand mixer or stand mixer, is a kitchen device that uses a gear-driven mechanism to rotate a set of "beaters" in a bowl containing the food or liquids to be prepared by mixing them.
Mixers help automate the repetitive tasks of stirring, whisking or beating. When the beaters are replaced by a dough hook, a mixer may also be used to knead.
A mixer may be a handheld mechanism known as an eggbeater, a handheld motorized beater, or a drill mixer. Stand mixers vary in size from small counter top models for home use to large capacity commercial machines. Stand mixers create the mixing action by either rotating the mixing device vertically (planetary mixers), or by rotating the mixing container (spiral mixers).
Hi,
I'm at a loss and need your help.
I have the attached mixer.
Water is leaking from the seal (yellow arrow)
I figured this is a washer replacement.
I've opened the screw cap (blue arrow) The screw inside is completely rusted and the head on it damaged.
The screw also turns with the handle...
Just looking for some advice, I have just fitted a new kitchen sink and both water pressures are the same in hot and cold on the mixer tap, both connected to tap flexies with shut off valves, however when hot is turned on it is not turning on the hot water for the boiler, previous sink had...
Hi, I'm new here. I have a basin with two individual taps, I want to change it to a mixer - the taps measure (centre to centre) 200mm. I have looked high and low to no avail, any ideas where to get one from? I don't want to make more holes or get a new basin if I can avoid it, I just want to...
Hi, I’m looking for a replacement cartridge for the one below . Is it a standard fitting or is it likely to have been discontinued? Tap us about 18 years old ( Blanco daras)
Had a new bathroom fitter, and the sink has these taps on Ideal Standard Tesi 1 lever Chrome effect Deck Mono Mixer Tap. The hot and cold water flow is reduced. But when the fitter took the taps off the water flow was increased, Could there be a problem with the new taps or is this because they...
Ashlea
Thread
cold
flow
hot
mixermixer tap
new
problem
tap
water
Hi all,
I'm having a lot of trouble trying to find replacement cartridges for this set of mixer taps. They were purchased approx 10 years ago. I have been told they are from ultra finishing, but they having looked at the pics state it's not one of theirs.
Any help identifying them would be...
Hi, I am trying to identify this thermostatic mixer valve to source a service kit. The water on off control seems to be getting stiffer, it's difficult for someone with limited hand grip. Photos of the valve attached. I can provide a photo of the control knobs fitted if that helps.
Thanks
Hello everyone
I need to replace this bath/shower mixer but cannot find any identification marks on it . Does anyone recognise it please. I need to replace with something similar
Many thanks
Paul
Hi All,
I hope you are doing well.
I have two copper pipes one 15mm and the hot water is 22mm.
My mixer tap has 2x 25mm (1 inch) female.
How to connect this up?
I cannot find any flexible connectors above 22mm. I also cannot find any reducers from 25 to 22mm.
What can I do?
Just replaced taps on bath so kids can get a shower in bath as well ,worked fine to started with then water wasn't hot so took them back and exchanged them ,now these are doing same any ideas anybody ?
We have a shower which has always been too hot no matter how you adjust the mixer temperature but recently it's really burning hot.
The shower is in a loft conversion and the plumbers teed off a downstairs shower to feed the bathroom upstairs. There are two isolation valves downstairs for hot...
The hot tap of a bath shower mixer has fine yellow sand like grit coming out, check all other taps in the house, this is the only one - combi boiler so no water tanks. Any ideas?
Likuan branded mixer taps, are they of good quality? Offered with the company for the water filters as a packaged . Please find link to company below
https://www.likuan.com/
Hi, there is a leak on the hot side of the taps under the lever but I can't see any screw to take out, how do you take them apart if there isn't a screw. Any help would be much appreciated.
Thanks
I'm probably missing something obvious, would welcome any suggestions on how I get access to the washers.
We have a matching bathroom suite and the bathroom sink mixer was a breeze to fix. The top of the taps popped off easy enough and the "collars" could be removed to expose a nut to unscrew...
Looking at a particular range (Vernis) of Hansgrohe taps and mixers. A 2 function bath mixer seems readily available but can only find a 1 function shower mixer. I will have a shower head and a separate hand shower so wanted a 2 function setup so I can switch between the two.
Can I use the...
Hi, I've seen a few posts about not using mains cold with gravity fed hot.
Ours is only about 0.1 bar for the hot.
The reasons given vary from possible backflow into hot cylinder to hard to get a good mix.
In that case how does the kitchen mixer tap work - that mixes gravity hot and...
Help!
I'm about to retile the shower area but I can't take off the handles or wall plate, unlike the two other Grohe mixers in my house there are no removable cap heads and there are no concealed screws. I am wondering if the shower handles just pull off (I've tried with a reasonable pressure...
My shower is controlled by what I think is a Trevi Hathaway Exposed Thermostatic Shower Valve L6800AA. The shower works fine but when I turn it to the off position it doesn’t shut off completely right away. I have to keep giving the handle an extra tweak until the flow eventually stops. Can...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.