You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
immersions
Immersion baptism (also known as baptism by immersion or baptism by submersion) is a method of baptism that is distinguished from baptism by affusion (pouring) and by aspersion (sprinkling), sometimes without specifying whether the immersion is total or partial, but very commonly with the indication that the person baptized is immersed in water completely. The term is also, though less commonly, applied exclusively to modes of baptism that involve only partial immersion (see Terminology, below).
Heno here. From Ireland. I'm a marine sparks but that doesn't qualify in any way to deal with electric and water. Pleasure to meet you all. I know the title of my 1st post might be moderated but I couldn't shorten it.
I've a Joule 300lt Cyclone tank. It has 2 Heatrod immersions with a Cotherm...
Hi,
I'm new here and have arrived on this forum as I have a question on the above.
I'm talking to a solar PV supplier about a 4kw system with which will come and Eddi controller which can feed 2 immersion heaters.
I'm a bit lost when it comes to the cylinders/thermal stores. We currently have...
Hi
I am on callout this week for my firm. Had one tonight, a thermal store immersions have both packed up. I need to try and sort it as no one is back in work until weds and the lady is elderly so dont want to leave her with no hot water for 5 days over christmas.
I know thermal stores...
Need to get a pair of immersions to replace existing, from what iv found out about Gerkros they went bust in 2009/2010 so no technical helpline.
Anyone worked on these and know the thread size, i know they are 14" - just cant be sure they are 1" 3/4 and dont really fancy draining it, removing...
mikeyc
Thread
cylinder
existing
heating
immersions
systems
unvented
unvented cylinder
Hi all. I am an absentee landlord because I work in the UAE and rent out my (future retirement) house. I rent it out through an agency. I suspect that the plumbers they use may be taking advantage of the fact I'm not there. They billed me 888 pounds (inc parts and VAT) in Sep 2011 for a new hot...
I have a RM stelflow unvented that I have just had fitted. my question is what does the thermostat settings in numbers relate to temperature wise? as it goes 1-6 or something similar not a temperature.
PLEASE HELP!!!!!!
I have replaced an economy 7 cylinder in a property (900x450) approx 120 litre. The tenant is complaining that the cylinder is not big enough. I went by a chart on the internet. Maybe i have got it wrong? The property is a terraced 2 bedroom with one bath, one basin and a...
I have fitted 2 immersions to the same cylinder in the last 8 months. Both have blown. They are 11in and bottom immersions on a huge cylinder that takes 3 hours to drain down. My electrician friend has checked it and cannot give an electrical reason for this to happen. Has this happened to...
Anyone else find that new Megaflo's now come with leaking immersion heaters?
Our last two installations had leaking immersion heaters which needed tightening - no really an issue, but just an observation and something to remember to check!
I appreciate they can loosen in transit and...
Hello my favourite people!
Ok dimplex pressurised cylind (similar to megaflow)
the cylinder is direct, in a newish build flat.
130ltr has two immersions, when you switch both both immersions on the water gets hot as it should but the cylinder loses heat very quickly, like if you have a shower...
Hi all,
Went to look at a job this evening - change the 2 immersions on a fortic cylinder. I want to pick them up before i go do it but haven't got a clue what size i need.
I was tired and the place smelt funny and i just wanted to get out of there so I never even measured the cylinder but it...
Any one else have trouble gettin any sort of unvented immersion. I can get them but its always a nightmare sourcing the right one. My merchants seem abit dumb when it comes to these.
Anyway anyone know where to get a 6kw immersion with 1 3/4 inch thread.
Cheers all.
Sent from my GT-I9100...
Hi all
I know im missing something here, i cant see a drain off tap or any way of doing it. I thourght i got it undone the immersion and got soaked not to metion the panic in the loft that the nice new room below was ruined. I cleaned up and made my excuses and left. I do have to go back...
Hi all,
Will be fitting a 1500 x 450 direct eco 7 cylinder for a customer - any recommendations on immersion sizes that will heat the water nicely on a cylinder this size?
Cheers
nysk2008
Thread
boost
cylinder
fitted
immersion
immersions
should
size
Hi all.
Hope someone can answer a question I have. Basically, first floor flat and ive got an unvented system which sole purpose is to heat the hot water for the taps. The system is about 2 years old now and both immersions in the cylinder have failed.
A while back the main immersion...
cheat007
Thread
changing
connections
cylinder
drain
gas
heater
hot
hot water
immersions
install
job
law
noise
parts
pressure
refill
regulations
safe
safety
system
taps
unvented
water
work
who ever use,s hawk ( yellow) paste on immersions should be shot , had to use blow torch to dis lodge old one . silcone sealant is the way . :)
WOLDEN
Thread
bath
cylinder
free
green
heater
hot
hot water
hot water cylinder
immersion heater
immersions
job
jobs
screw
seal
stuck
supply
touch
washer
water
work
yellow
Hi, I installed a new eco 7 cylinder back in Decmeber with new immersions and the customer just called me because she has no hot water.
when i got round there i checked the fuses on the board and the spurs, power was there, i checked the immersion, power was there but no buzzing when i switched...
chrisplumb
Thread
connect
cylinder
eco
hot
hot water
immersions
inside
no hot water
not working
power
supply
test
water
working
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.